Wasp WLS8400FZ Especificações Página 166
- Página / 394
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
WLS 8400 Product Reference Guide
8-20
Convert UPC-E to UPC-A
When enabled, UPC-E (zero suppressed) decoded data is converted to UPC-A format
before transmission. After conversion, the data follows UPC-A format and is affected by
UPC-A programming selections (e.g., Preamble, Check Digit).
When disabled, UPC-E decoded data is transmitted as UPC-E data, without conversion.
Convert UPC-E to UPC-A
(Enable)
*Do Not Convert UPC-E to UPC-A
(Disable)
- WLS 8400 3
- Product Reference Guide 3
- Contents 5
- Chapter 5 7
- Chapter 6 7
- RS-232 Interface 7
- Chapter 7 8
- Chapter 8 8
- Chapter 9 10
- Miscellaneous Scanner Options 10
- Chapter 10 11
- Advanced Data Formatting 11
- Appendix D 13
- Numeric Bar Codes 13
- Glossary 13
- About This Guide 15
- Chapter Descriptions 17
- Notational Conventions 18
- Related Publications 18
- Service Information 18
- Wasp Support 19
- Getting Started 21
- Unpacking the Scanner 24
- Setting Up the Scanner 25
- Removing the Interface Cable 27
- Configuring the Scanner 27
- Scanning 29
- Beeper Definitions 32
- LED Definitions 33
- Scanning in Hand-Held Mode 34
- Scanning in Hands-Free Mode 36
- Decode Zone 37
- Maintenance and Technical 39
- Specifications 39
- Maintenance 41
- Troubleshooting 42
- Technical Specifications 45
- Scanner Signal Descriptions 47
- User Preferences 49
- Beeper Volume 54
- *High Volume 54
- Power Mode 55
- Laser On Time 55
- Beep After Good Decode 56
- *Beep After Good Decode 56
- Trigger Mode 56
- Trigger Mode (continued) 57
- Aim Duration 58
- Keyboard Wedge Interface 59
- Male DIN Host 62
- Female DIN Keyboard Keyboard 62
- FN1 Substitution Disable 5-15 64
- Parameter Default Page Number 64
- Keyboard Wedge Host Types 65
- *North American 66
- Keystroke Delay 68
- Keystroke Delay (continued) 69
- Intra-Keystroke Delay 69
- Caps Lock On 70
- Caps Lock Override 71
- Convert Wedge Data 72
- *Do Not Convert Wedge Data 72
- FN1 Substitution 73
- Send Make and Break 73
- Keyboard Maps 74
- Figure 5-4. IBM PC/AT 75
- Figure 5-5. NCR 7052 32-KEY 75
- Figure 5-6. NCR 7052 58-KEY 76
- Serial Port Connector to 92
- Interface 92
- Power supply 92
- RS-232 Default Parameters 93
- RS-232 Host Parameters 94
- RS-232 Host Types 97
- RS-232 Host Types (continued) 98
- Baud Rate 98
- Baud Rate (continued) 99
- *Baud Rate 9600 99
- Parity (continued) 101
- Check Receive Errors 101
- Stop Bit Select 102
- *1 Stop Bit 102
- Data Bits 102
- Hardware Handshaking 103
- RTS/CTS Option 1 104
- Standard RTS/CTS 104
- RTS/CTS Option 2 105
- RTS/CTS Option 3 105
- Software Handshaking 106
- ACK/NAK with ENQ 107
- XON/XOFF 107
- Host Serial Response Time-out 108
- *Minimum: 2 sec 108
- RTS Line State 109
- *Host: Low RTS 109
- Beep on <BEL> 110
- Intercharacter Delay 111
- *Minimum: 0 msec 111
- Mode A is selected 112
- Ignore Unknown Characters 113
- ASCII / Character Set 114
- USB Interface 119
- Introduction 121
- Connecting a USB Interface 122
- USB Default Parameters 124
- USB Host Parameters 125
- USB Keystroke Delay 128
- *No Delay (0 msec) 128
- USB CAPS Lock Override 129
- USB Ignore Unknown Characters 130
- Emulate Keypad 131
- Function Key Mapping 132
- Simulated Caps Lock 133
- Convert Case 133
- ASCII Character Set 134
- Symbologies 147
- Scanning Sequence Examples 151
- Errors While Scanning 151
- Symbology Default Parameters 152
- Enable/Disable UPC-A 156
- *Enable UPC-A 156
- Enable/Disable UPC-E 156
- *Enable UPC-E 156
- Enable/Disable UPC-E1 157
- *Disable UPC-E1 157
- Enable/Disable EAN-13 157
- *Enable EAN-13/JAN-13 157
- Enable/Disable EAN-8 158
- *Enable EAN-8/JAN-8 158
- Enable/Disable Bookland EAN 158
- *Disable Bookland EAN 158
- *Transmit UPC-A Check Digit 161
- *Transmit UPC-E Check Digit 162
- *Transmit UPC-E1 Check Digit 162
- UPC-A Preamble 163
- *System Character 163
- UPC-E Preamble 164
- UPC-E1 Preamble 165
- Convert UPC-E to UPC-A 166
- Convert UPC-E1 to UPC-A 167
- Code 128 168
- Enable/Disable UCC/EAN-128 169
- *Enable UCC/EAN-128 169
- Enable/Disable ISBT 128 169
- Enable/Disable Code 39 170
- *Enable Code 39 170
- *Disable Trioptic Code 39 170
- Convert Code 39 to Code 32 171
- Code 32 Prefix 172
- *Disable Code 32 Prefix 172
- Set Lengths for Code 39 173
- Code 39 - Length Within Range 174
- Code 39 - Any Length 174
- *Disable Code 39 Check Digit 175
- Transmit Code 39 Check Digit 176
- Code 39 Full ASCII Conversion 177
- *Disable Code 39 Full ASCII 177
- Enable/Disable Code 93 178
- *Disable Code 93 178
- Set Lengths for Code 93 178
- Code 93 - Length Within Range 179
- Code 93 - Any Length 179
- *Disable Code 11 180
- Set Lengths for Code 11 180
- Code 11 - Any Length 181
- Code 11 - Length Within Range 181
- One Check Digit 182
- Two Check Digits 182
- Transmit Code 11 Check Digits 183
- Interleaved 2 of 5 (I 2 of 5) 184
- I 2 of 5 - Any Length 186
- *Disable 187
- Transmit I 2 of 5 Check Digit 188
- Convert I 2 of 5 to EAN-13 188
- (Disable) 189
- Discrete 2 of 5 (D 2 of 5) 190
- Codabar (NW - 7) 192
- Set Lengths for Codabar 193
- Codabar - Length Within Range 194
- Codabar - Any Length 194
- CLSI Editing 195
- *Disable CLSI Editing 195
- NOTIS Editing 195
- *Disable NOTIS Editing 195
- Enable/Disable MSI 196
- *Disable MSI 196
- Set Lengths for MSI 196
- MSI - Two Discrete Lengths 197
- MSI - Length Within Range 197
- MSI Check Digits 198
- *One MSI Check Digit 198
- Transmit MSI Check Digit(s) 199
- MSI Check Digit Algorithm 199
- *MOD 10/MOD 10 199
- RSS (Reduced Space Symbology) 200
- *Disable RSS Expanded 201
- Convert RSS to UPC/EAN 201
- Redundancy Level 202
- Redundancy Level 3 203
- Redundancy Level 4 203
- Security Level 204
- Security Level 2 205
- Security Level 3 205
- Bi-Directional Redundancy 206
- Transmit Code ID Character 211
- Scan Angle 212
- Prefix/Suffix Values 212
- Scan Data Transmission Format 213
- FN1 Substitution Values 215
- Transmit “No Read” Message 215
- *Disable No Read 215
- Using ADF Bar Codes 219
- ADF Bar Code Menu Example 220
- Rule 2: The UPC Scanning Rule 221
- Alternate Rule Sets 221
- Default Rules 224
- Special Commands 225
- Quit Entering Rules 226
- Disable Rule Set 227
- Criteria 228
- RSS Expanded 229
- Code Types (continued) 230
- Code Lengths 233
- Code Lengths (continued) 234
- Specific String at Start 239
- Any Message OK 240
- Numeric Keypad 241
- Numeric Keypad (continued) 242
- Rule Belongs To Set 243
- Send Data 244
- Send Data (continued) 245
- Setup Field(s) 248
- Move Cursor 249
- Send Pause 249
- Skip Ahead 250
- Skip Ahead (continued) 251
- Skip Back 252
- Skip Back (continued) 253
- Send Preset Value 254
- Modify Data 255
- Modify Data (Continued) 256
- Pad Data with Spaces 257
- Pad Spaces To Length 29 262
- Pad Spaces To Length 30 262
- Stop Pad Spaces 262
- Pad Data with Zeros 263
- Pad Zeros To Length 29 268
- Pad Zeros To Length 30 268
- Stop Pad Zeros 268
- Beep Once 269
- Beep Twice 269
- Beep Three Times 269
- Control Characters 270
- Send Control \ 275
- Send Control ] 275
- Send Control 6 275
- Send Control 275
- Keyboard Characters 276
- Send ALT Characters 292
- Send Alt 6 297
- Send Alt 297
- Send Keypad Characters 298
- Send Function Key 304
- Send Function Key (continued) 305
- Send Right Control Key 313
- Send GUI 2 314
- Send GUI 3 314
- Send GUI Y 320
- Send GUI Z 320
- Turn On/Off Rule Sets 321
- Alphanumeric Keyboard 323
- Standard Default Parameters 341
- Programming Reference 351
- Symbol Code Identifiers 353
- AIM Code Identifiers 354
- Sample Bar Codes 357
- 123 45 67890 5 359
- 1234 56 5 359
- 1234 56 2 359
- 3 45678 9 0 12340 360
- 1234 5 670 360
- Trioptic Code 39 361
- Interleaved 2 of 5 362
- 72-67133-01 394
- Revision A — February 2004 394
Manuais e produtos relacionados com Leitores de códigos de barras Wasp WLS8400FZ
Leitores de códigos de barras Wasp WPS100 Especificações
(466 páginas)
(466 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais